XRotor Flight Controller F7
Super hardware and running speed Equipped with STM32F722 MCU which has powerful computing ability and fast running speed, and high sensitivity MPU6500 six-axis motion sensor. It can perfectly support bidirectional DShot digital throttle communication. The integrated OSD chip can adjust and set each OSD parameters in FC parameter adjustment software and radio, which is simple and convenient. On-board large capacity Flash memory chip can record and store more flight logs, which is convenient for users to debug aircraft based on flight data.
Special interface for DJI image transmission system With DJI image transmission system port, equipped with corresponding flat cable (FC has been equipped), can avoid welding, realize plug and play.
On-board 5V & 10V dual BEC circuit FMU integrates with 10V BEC circuit. It can supply super power output for image transmission and 10V LED devices.
On-board Pit Switch module FC integrated Pit Switch module can open or close VTX by radio after being adjusted on FC parameter software. Easy and convenient.
Perfectly support firmware of various FPV It support the firmware of BetaFlight , Cleanflight , Butterflight , inva and other mainstream FPV, and can use corresponding parameter adjustment software to adjust various parameters, making the FC more suitable for various FPV flight and race.
Unique installation design and shock absorption structure The double hole distance mounting hole design (30 * 30MM & 20 * 20MM) can adapt to different frames. The unique flexible flat cable connection mode (The effect is better with hobbywing tower 4in1 ESC ), and the shock absorption mechanism of installation hole, can effectively reduce the impact of external vibration on FC high-sensitivity components, and make the flight more stable and accurate.
Perfectly match with Hobbywing ESC Match with Hobbywing tower 4in1 ESC, easy to install and wire. The appearance is more beautiful.
Volt/Amp monitoring port allows users to check the battery voltage (BAT port) and current (CRT port , extra current meter is needed).
Buzzer output port allows users to connect external buzzer(s) to the FC for warning or informing the flight status of the aircraft.
Micro USB port allows users to connect the FC to a PC to flash firmware and adjust parameters. 
Switch module of board load graphic transmission(VTX) can use remote control to control switch of graphic transmission.
Double M3 mounting holes with damping aprons.
Model    Micro F7 Flight Controller Convertible  
SKU 31003002
Application    FPVs with 130-300mm FPVs Diagonal Wheelbase
Firmware     HOBBYWING_XROTORF7CONV
FC Programming    supported
Programming via Betaflight/Cleanflight-configurator and Others
Compatible with (Modes)    PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600, DShot1200, Proshot1000 and etc
Compatible with (Transmitters) PPM, Spektrum, SBUS, SUMD, SUMH, XBUS, IBUS, JETIEXBUS, CRSF, SRXL, and etc.
OSD    Buit-in / Fit for DJI VTX system plug and play port
Voltage Monitoring    Supported
Current Monitoring    Supported
External Buzzer    Supported
LED Control    Supported
USB Port    MicroUSB
Timing    Supported
Motor Rotation    Supported
Mounting Holes 30.5x30.5mm & 20x20mm
 
XRotor FPV G2 45A 4in1 ESC
20X20mm ultra-small mounting hole spacing design, further reducing size and weight.
Combined with a new generation of 32-bit ARM F4 processor, the operating frequency
is further increased to 120MHz. Specially tailored for competition level FPV!
The operating frequency is further increased to 120MHz!
 
96KHz Dynamic PWM
Supports 48KHz-96KHz PWM frequency,
and can be dynamically adjusted adjusted
for precision throttle control
 
Product Number: 30902045
Current: 45Ax4
Input Voltage: 3-6S Lipo
Applications: 100-300mm FPVs